Features:
Motor Specifications:
ESC Specifications:
- Feigao model 1208425L with Very light (7g including wires & connector)
10AM ESC - Mini size brushless motor, ideal for upgrade from brushed motor to
brushless motor, for some light model plane. - light weight, powerful and ideal for light model plane upgrade.
Motor Specifications:
- Turn:25T
- RPM/V:5866
- Size: 12mmX30mm
- Shaft size:1.5mm
- Weight:17g(0.60oz)
ESC Specifications:
|
1.Extremely Low Resistance
2.High rate PWM)
3.Sixteen cells MAX (with BEC disabled)
4.BEC (1.5A/4A) provides power to receiver and servos -
5.User Programmable Features:
Low-voltage cutoff ( 2cells or 3cell LI-PO auto setting)
Brake
Throttle Range self-adjusting
6.Soft Start ramp up
7.Runs motor in forward /reverse
8.Auto Motor Cutoff with Reset
9.Safe power on arming program ensures motor will not accidentally turn on
10.Low torque soft start.
11.Auto shut down when signal is lost or radio interference
User guide
1.The main power cable can maximum of 20 cm length.
2.It is recommended to solder the cables directly to the power pack.
3.Plug the JR connector into the receiver throttle channel.
4.If using micro servos, it is necessary to reduce the number of servos by one.
Installing procedure:
1.Attach the motor to the motor mount with the screws provided.
2.Main power packs should be connected at one attempt. Avoid multiple touches
of the connectors.
3.Power on the transmitter and check the throttle channel travel settings are
+/-100% (for computer system radios.)
4.Power on the speed controller .
You must hear one 'beep'. Between switching on and hear the 'beep' the throttle
stick must not be moved .If you do not hear a 'beep', power off the controller, and
wait for 5 seconds then repeat the procedure again .
5.The position of 'full throttle' will be adjusted automatically.
6.The speed controller is 'brake' activated initial.If you want to turn off the brake
,you have to :
- Switch on the transmitter and move the stick to 'full throttle'.
- Connect the power pack and turn on the receiver switch .
- Wait 5 seconds.
- After 5 seconds you will hear 4 tones.
- Move the throttle stick fast to the 'stop' position; you will hear two 'beeps'.
- The 'brake' is now turned off.
7.If you want to activate the brake again, repeat step '6' again.
8.Only have to exchanging the position of any two wires connected to the motor
then you can reversing the motor .
2.High rate PWM)
3.Sixteen cells MAX (with BEC disabled)
4.BEC (1.5A/4A) provides power to receiver and servos -
5.User Programmable Features:
Low-voltage cutoff ( 2cells or 3cell LI-PO auto setting)
Brake
Throttle Range self-adjusting
6.Soft Start ramp up
7.Runs motor in forward /reverse
8.Auto Motor Cutoff with Reset
9.Safe power on arming program ensures motor will not accidentally turn on
10.Low torque soft start.
11.Auto shut down when signal is lost or radio interference
User guide
1.The main power cable can maximum of 20 cm length.
2.It is recommended to solder the cables directly to the power pack.
3.Plug the JR connector into the receiver throttle channel.
4.If using micro servos, it is necessary to reduce the number of servos by one.
Installing procedure:
1.Attach the motor to the motor mount with the screws provided.
2.Main power packs should be connected at one attempt. Avoid multiple touches
of the connectors.
3.Power on the transmitter and check the throttle channel travel settings are
+/-100% (for computer system radios.)
4.Power on the speed controller .
You must hear one 'beep'. Between switching on and hear the 'beep' the throttle
stick must not be moved .If you do not hear a 'beep', power off the controller, and
wait for 5 seconds then repeat the procedure again .
5.The position of 'full throttle' will be adjusted automatically.
6.The speed controller is 'brake' activated initial.If you want to turn off the brake
,you have to :
- Switch on the transmitter and move the stick to 'full throttle'.
- Connect the power pack and turn on the receiver switch .
- Wait 5 seconds.
- After 5 seconds you will hear 4 tones.
- Move the throttle stick fast to the 'stop' position; you will hear two 'beeps'.
- The 'brake' is now turned off.
7.If you want to activate the brake again, repeat step '6' again.
8.Only have to exchanging the position of any two wires connected to the motor
then you can reversing the motor .
Free Shipping on orders over $100.00
 | |  | |  |
Home
Airplanes
Li-Poly Batteries
Brushless Motors
Combo Packages
Engines
Helicopters & Parts
Radios & Receivers
Simulators
Servos & Gyros
Speed Controllers
3rd party fulfillment airplanes
Weekly Special
Accessories
Chargers
Ducted Fans
Motor mounts & Shafts
Props
Prop Adapters
Prop Savers
Wires & Connectors
Other Fun Sites
A-Bikes
Aquaskippers
Auto Electric Guns
SkipShoes
Silent Windmills
Snowmobile Capital
Very Cheap Tours
Airplanes
Li-Poly Batteries
Brushless Motors
Combo Packages
Engines
Helicopters & Parts
Radios & Receivers
Simulators
Servos & Gyros
Speed Controllers
3rd party fulfillment airplanes
Weekly Special
Accessories
Chargers
Ducted Fans
Motor mounts & Shafts
Props
Prop Adapters
Prop Savers
Wires & Connectors
Other Fun Sites
A-Bikes
Aquaskippers
Auto Electric Guns
SkipShoes
Silent Windmills
Snowmobile Capital
Very Cheap Tours